![]() Once you have a recent U-Boot, you can have a look at the supported display for your board by issuing: > fbpanel clock-frequency hactive vactive hback-porch hfront-porch vback-porch vfront-porch hsync-len vsync-len hdmi: 1280x720M60:m24x1,50:74161969,1280,720,220,110,20,5,40,5 74161969 1280 720 220. # This is a command added to U-Boot by TS to read the baseboard ID on our # System on Module devicesÄ®cho $-ts7970. You can follow the v2016.03 instructions. # The most important command is help # This can also be used to see more information on a specific command help i2c This mode will also check for a USB mass storage device to use for production purposes. To break into the U-Boot console, press and hold the SW1 button while the unit is being powered up. SF: Detected N25Q64 with page size 256 Bytes, erase size 4 KiB, total 8 MiBÄ«y default the device will boot to SD or eMMC depending on the status of the "SD Boot" jumper on startup. On a normal boot the output should be similar to the output below: U-Boot is a general purpose bootloader that is capable of booting into common Linux distributions, Android, Windows, or custom software OSes. U-Boot provides support for loading data from various mediums this allows booting a kernel from SD, eMMC, SATA, NFS, or USB. In examples, to show the contents of files, the output from commands, the C code. The i.MX6 processor loads U-Boot from the on-board 8 MiB SPI flash. Conventions used in this manual This list shows the typographical conventions used in this guide: Style Style Style Used for file and directory names, variables in commands, URLs and new terms.This library allows you to communicate with I2C / TWI devices. Before attempting to test out the touchscreen, first install the driver as described in. The Servo library allows an Arduino board to control RC (hobby) servo motors. How do you do it? By the way,I ported and used U-Boot 2011.09 for this purpose.I used i2c-tool over Linux but it says UU which means driver is used by Linux and it doesnt let me dump or anything else.This platform uses U-Boot as the bootloader to launch the full operating system. I just ran these 2 commands in the terminal and my touch screen works. Just add that to your low-level Linux startup code before the ports have been reprogrammed to be I2C, or even better, add some simple code to your Bootstrap (RedBoot, U-Boot or whatever) to do that for you. Firstly i read my eeprom, then i tried to write byte by btye.Then i read again but nth happened.Then i tried to fill with 0xAA again it didnt succeed. Just reprogram the I2C Clock pins as a GPIO and toggle it on and off (at 400kHz or so) nine times. define CONFIGOFCONTROL and CONFIGOFSEPARATE add your device tree files to arch//dts update the Makefile there Add stdout-path to your /chosen. You can follow the v2016.03 instructions.Type 'help' or '' for a complete listing of available commands. U-Boot commands The list of U-boot commands can be accessed while in the U-Boot prompt. I could change the pin type to output by modifying the code and recompiling U-Boot, but actually changing the value using the gpio command didnât work. I havenât been able to change its value so far. i2c: i2c controller: ethernet lite: EMAC lite. I poked around a bit using the helpful i2c U-Boot command and also tried to use the gpio command for BACKLIGHTEN (GPIO1IO10 per schematic). I tried with U-Boot using I2C commands.You can see my logs below. Add tool chain to path and then set tool chain as below. This will allow you to use i2c commands at the u-boot command line (as long as you set CFGCMDI2C in CONFIGCOMMANDS) and communicate with i2c based realtime clock chips. From the UBoot command prompt, you can display the environment variables and their values by using the printenv command. ![]() We have custom Am335x board with eeprom.We want to shape our eeprom like BeagleBone (I mean name,version,serial etcâ¦). Defining either of (but not both of) CONFIGHARDI2C or CONFIGSOFTI2C will include the appropriate I2C driver for the selected cpu. The U-Boot environment variables determine exactly how a board is supposed to boot.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |